Welcome New User! ( Create Account | Sign In )

Maximize

You are here: Home Categories Autos & Transportation My van will turnover but wont start. changed plugs, rotor, cap module new wires everything was working fine ti...

Previous | Next

I have a 1999 s-10 4.3 started fine one day the next nothing. checked fuel pressure 58l also checked spark it also is good. c... Tomorrow to see if it is ok also going to check the plugs

I have a 1990 mecury topaz gls. i've changed the spark plugs, wires, fuel filter,rotor and cap .full tank of gas with fuel in... changed the thermostat. once i start the car it idles so so. but once i put it in gear it...

I have a 83 chevy pickup cannot get a spark has brand new coil,ign.module ,cap&rotor,wire s help! Friend of mine replaced all of these.afterwords he turns truck on, the mat lands on the accelorator...

My 93 blazer 4.3 mpi vin w wont start I have changed fuel pump, fuel reg., distributor,cap,wire s,plugs,tps,cleand egr,coeds only...

Truck wont start after running 1987 bronco 2 replaced coil plugs cap rotor has proper fuel pressure has spark

Get paid for participating

Ask questions - It's FREE Get answers within minutes.

Fun, fast and easy. Share your opinions with our community. Earn money for answering. See how.

This Question has not been awarded yet.

Post your answer now!

Find more related questions to My van will turnover but wont start. changed plugs, rotor, cap module new wires everything was working fine till now it has started this again? what c

Question

Submitted 185 days ago...

krusty338

New User (1)

My van will turnover but wont start. changed plugs, rotor, cap module new wires everything was working fine till now it has started this again? what c

Van will turnover but not start

Share | Abuse |

Answers

Answer 1 / 2 - Submitted 185 days ago...

btemple501

Professor (1,007)

You need to find out what you are missing, do you have spark? Fuel? proper fuel pressure? some more information would be helpfull.

Share | Link | Abuse

Answer 2 / 2 - Submitted 185 days ago...

fubar

Contributor (95)

Clogged catylitic converter. had the same prob with my dodge. replaced the motor and it wouldnt start. knew it was good motor, had spark, fuel, 55psi pressure and timed correct. wanted to start but didnt catch. spent 1150.00 to find it was the cat. any way you can pull oxy sensor to find out for sure? this could relieve enough back pressure to at least get it started and know for sure.

Share | Link | Abuse

Answer This Question Now

My van will turnover but wont start. changed plugs, rotor, cap module new wires everything was working fine till now it has started this again? what c

If your Answer is chosen as the “accepted” answer, you will earn ongoing royalties on this thread.
Simply type your Answer in the box below and post your answer.

Learn more about how WebAnswers.com works

Related Questions

After tune up truck won't start.

After replacing the cap, rotor,plugs and new heavier plug wires (8.5mm MSD) my 4.3l chevy won't start. I have spark , fuel at the throttle body. It tried to fire the very first time after the change, but nothing...

Open | Category: Autos & Transportation | 1 Reply

Blazer wont start

Ive changed everything from the camsensor to the starter ,battery , wires , plugs , and distrubutor, cap and rotor and it still wont start . Im guessing it in time since it cranks freely now. but i cant even getr...

Open | Category: Maintenance & Repairs | 1 Reply

2000 nissan frontier 3.3l misses

I changed plugs wires cap and rotor,knock sensor and it keeps on missing.

Open | Category: Autos & Transportation | 0 Replies

B18 sputters around 4500 to 5000 what could cause this

Changed plugs, wires. thinkin its the cap or rotor.

Open | Category: Autos & Transportation | 0 Replies

My check engine light comes on and stays

Didn't disconnect battery,changed new plugs and cap rotor,wires. whats up with the engine light?

Open | Category: Maintenance & Repairs | 1 Reply